12db圆筒天线制作公式

直接输入频道，圆筒直径就可以自动生成相关资料
Building the Cylinder (Can) Waveguide
圆筒天线的制作
We chose to build the antenna for 2.442GHz, or channel 7, as this is close to the center of the 13 channels available to us (US designs use channel 6 (2.437Ghz), as they have 11 channels). I have included a key lengths calculator in the form below. Nb.Rectangular waveguides use a different formulae (see Rectangular Waveguide).

Frequency频率	b/g Chnl 1 b/g Chnl 2 b/g Chnl 3 b/g Chnl 4 b/g Chnl 5 b/g Chnl 6 b/g Chnl 7 b/g Chnl 8 b/g Chnl 9 b/g Chnl 10 b/g Chnl 11 b/g Chnl 12 b/g Chnl 13 b/g Chnl 14 a Chnl 34 a Chnl 36 a Chnl 38 a Chnl 40 a Chnl 42 a Chnl 44 a Chnl 46 a Chnl 48 a Chnl 52 a Chnl 56 a Chnl 60 a Chnl 64 a Chnl 149 a Chnl 153 a Chnl 157 a Chnl 161	GHz
Diameter   直径		mm (Inside Measurement)
Free Space Wavelength		mm
Waveguide Wavelength		mm
最大频率		GHz
最小频率		GHz
截止频率		GHz
Probe Length		mm 探针长度
Open End to Probe		mm (Open End to probe center)
Probe to Reflector探针到圆筒后面反射体		mm (Probe center to Reflector)
Inside Length		mm (Reflector to Opening

The final product only needs to be accurate to about 1mm as this will only shift the frequency within the range of the 802.11 spectrum. A smaller cavity length will shift the frequency response to that slot to a higher channel. A longer slot cavity length will shift it down.

Methods and madness
I measured to .1mm using vernier callipers, on the assumption that errors in cutting might bring that closer to the 1mm error mark. There are only one to make, and you can't go too wrong, i.e. the probe (N-Socket) position.

Misc Notes

    * The probe is a 2mm diameter copper wire soldered into an N-Socket and cut to 31mm (1/4 free space wavelength, including the protruding bit of the N-Socket).
    * 探针采用的是2mm直径的铜线焊接在N接头的槽上。探针长度为31mm，包含N接头突起的部分。

    * The N-Socket is held down with nylon screws. If you use metal screws, use stainless steal ones and keep them short so they don't protrude into the cavity.
    * Water in the antenna, or spider and insects will be a problem. One suggestion is to seal around the edges of the reflector with silicone and cover the open end with a piece of plastic (microwave friendly and thin).

N-Socket with 1/4 wavelength copper wire (including the length of the bit of the N-Socket it is soldered into). This becomes the probe for the antenna.

本文出自家电维修网: http://www.bjjdwx.com/wz/2008-12-02/1072.html欢迎转载，转载请保留链接。

上一篇：LM317T应用电路

下一篇：2.4G WIFI高增益天线制作总结

昵称 (必填)

验证码 (必填)